Ioline 3700 Driver
This procedure restores plotter settings to the factory default. Care must be taken not to over tighten, as this will damage the pen carriage. Check the carriage that holds your pen or Artpro knife. Check the height of the pen in the raised position at the right, center, sis 650 651 m650 740 driver for windows 7 and left limits.
Check the dashpot adjustment. If the pen carriage does not line up properly with the pen stalls, further repair will have to be made. Move the pen to this location. The force that the pen or knife exerts on plotting media may be varied by adjusting the pen-down adjustment spring tension. Download list - Download multiple files at once View, edit and download your entire list of software and drivers here.
How to erase the autoview. Visually inspect the Y-axis belt for cracks or damage. If there is insufficient damping, the pen will strike the plot media with too much force, causing spots or even holes at the line starts.
You must have Chinese fonts available for the program to properly display. Replace the dust cover, taking care to compress the pen carriage damper wheels inside the dust cover before lowering it into place. Turn off the power to the plotter.
Tighten the mounting screw and verify that the switch does not touch the belt on either side. Binhexed Macintosh Version. There may be side play in the pen holder.
Pairs of measuring marks for both x and y axes are indicated on the plot in either inches or centimeters. When properly adjusted, the empty pen holder will fall under its own weight. When removing or replacing the cover, use caution to move it slowly in the vertical direction, rocking gently to engage or disengage the two damper wheels. To check this, turn the round, stainless steel traverse rods manually. When the media hits a flat spot on a chartwheel, the media slips.
Need help troubleshooting? If you are cutting with an Artpro cutter, you must balance the cutting depth of the blade with the pen force. Subscription auto-renews at the end of the term Learn more.
Generic Windows Drivers Ioline does not write generic Windows drivers. The list of all available drivers for your product is shown above.
HP DeskJet 3700 All-in-One Printer series
Not sure which drivers to choose? We were unable to find any drivers for your product. Solution and Diagnostic Data Collection.
Remember, the x direction is always in the paper motion direction, and the y direction is always the pen motion direction. Finally, turn the adjustment screw one-half to one full turn counterclockwise, further decreasing the amount of damping.
The adjustment screw should be turned counterclockwise during plotting until the problem is resolved. As you can see, you can set all the user parameters from your computer keyboard, which is easier to use than the keypad on the plotter. These machines were modified pen plotters, probably lates technology.
The plotter will move the pen up and down rapidly while continuously stepping both drive motors. Stretching the spring gives the knife more tension so the knife responds faster to picking up the blade off the media. This website is using cookies. No matter where you locate the carriage, it should not rise up or lower when you turn the traverse rods. Question Anyone heard of Funsun printers?
Maintaining updated Ioline software prevents crashes and maximizes hardware and system performance. The blade offset for knife blade from Ioline is marked on the package in which they are shipped.
The pen should lift at least. Check the set screws on the coupling between the motor and the gritshaft. Europe, Middle East, Africa. The easiest way to program the memory of the plotter is by using the Plot Utility Disk. The desired clearance is approximately.
How is the Gold Competency Level Attained? Please verify your product is powered on and connected, then try again in a few minutes. If not, readjust the position of the limit switch.
Raise the rear idler wheel to clear the pen lift belt and rotate the pen lift plate assembly until the centers of the two sprockets form a line perpendicular to the traverse rods. Push the adjustment level up or down to increase or decrease the pen force.
This parameter is the amount of blade offset or the distance from the tip of the blade to its center of rotation. Pen-down motion can be damped by an adjustable dashpot located next to the pen solenoid. Lock the wheels and tug the media. The tension of the spring in the Knife assembly must be increased. The difference between the measured distance and the nearest whole inch or centimeter should be small.
Or, view all available drivers for your product below. To correct, tighten the cone-point bearing screws. Move the carriage to different locations on the rods. The scale commands operate independently of the micro-calibration resolution.
HP Customer Support
Plot is good at the center but bad at the edges. Pen-rail height adjustment.
- Lenovo iel10 driver for windows 7
- Drivers for microcam cool icam
- Asm104xusb3 drivers for windows 10 download
- Dfi lanparty ut nf4 sli dr expert drivers for windows xp
- Asus p5b deluxe sata driver
- Lg optimus 3d omap4430 driver
- Dell 720 drivers for windows download
- Winfast 760m02-gx-6lrs driver for windows mac download
- Asus a3a drivers download
- Aero wddm driver
- Xerox workcentre 7665 driver
- Sharp mx-2600n pcl5c drivers for windows 7 download
- Fuji xerox c2100 driver
- Samsung n150 graphics drivers for windows xp download